Guides and Practical Tips

Melting point of aluminium and its alloys – table and casting temperatures

What the melting point of aluminium is, why alloys melt over a temperature range and at what temperature aluminium is cast in sand moulds, permanent moulds and high-pressure dies.

Published: 6 min readPoznań Foundry Team

Table of contents (9)
  1. 01What is the melting point of aluminium?
  2. 02Why do aluminium alloys melt over a temperature range?
  3. 03Melting point of aluminium alloys – table
  4. 04At what temperature is aluminium cast?
  5. 05How much energy does it take to melt aluminium?
  6. 06Heat treatment temperatures and the melting point
  7. 07Frequently asked questions
  8. 08Aluminium castings – we will select the alloy and the process
  9. 09Sources and standards

The melting point of aluminium is 660.3 °C, or more precisely 660.323 °C according to the International Temperature Scale ITS-90. Aluminium alloys do not have a single melting point but a range between solidus and liquidus: for the popular casting alloy AlSi7Mg it is about 555–615 °C, and for alloy 7075 about 475–635 °C. In a foundry the metal is superheated above the liquidus, usually to 650–760 °C, depending on the casting method.

In brief

  • Pure aluminium melts at 660.3 °C, and this value is one of the fixed points of the International Temperature Scale ITS-90.
  • Aluminium alloys melt over a temperature range: they begin to melt at the solidus temperature and are fully liquid above the liquidus.
  • Silicon lowers the melting point, and the Al–Si eutectic melts at about 577 °C, which is why silumins are so well suited to casting.
  • The casting temperature is several tens to over a hundred degrees above the liquidus and depends on the method, wall thickness and alloy.
  • Overheating the metal more than necessary increases the amount of dissolved hydrogen and oxides and, as a result, the porosity of castings.

What is the melting point of aluminium?

Pure aluminium with a purity of 99.99% melts at 660.3 °C. This point is so reproducible that it serves as a fixed point of the ITS-90 scale for calibrating thermometers. Commercially pure aluminium with a purity of 99.5% melts slightly lower and over a narrow range, for example alloy EN AW-1050A at about 646–657 °C.

At its melting point liquid aluminium has a density of about 2.37 g/cm³, and during solidification its volume decreases by about 6–7%. How density depends on temperature and composition is discussed in our article on the density of aluminium.

Melting point of aluminium compared with other metals

Aluminium melts at a much lower temperature than steel or cast iron. This lowers energy costs and allows the use of reusable steel moulds such as permanent moulds and high-pressure dies.

MaterialMelting point
Pure aluminium660,3 °C
Magnesiumapprox. 650 °C
Gray cast ironapprox. 1150–1250 °C
Carbon steelapprox. 1420–1500 °C
Titaniumapprox. 1668 °C

Why do aluminium alloys melt over a temperature range?

Alloying elements such as silicon, copper and magnesium cause the alloy to change from solid to liquid gradually. The solidus temperature is the point at which the first liquid appears, and the liquidus temperature is the point above which all of the metal is liquid. Between them the material is in a mushy, semi-solid state.

The role of silicon and the Al–Si eutectic

Silicon lowers the melting point of aluminium down to the eutectic point at about 12.6% Si, where the alloy melts at a single temperature of about 577 °C. That is why eutectic alloys of the AlSi12 type have a very narrow freezing range and excellent fluidity, while hypoeutectic alloys such as AlSi7Mg solidify over a wider range. More about this group of alloys can be found in our article on silumin.

Freezing range and casting quality

The width of the range between solidus and liquidus affects how the alloy behaves in the mould. Alloys with a narrow range solidify layer by layer and are easier to feed, while alloys with a wide range solidify in a mushy manner and are more prone to dispersed shrinkage porosity and hot tearing. These relationships are described in our article on aluminium casting defects.

Melting point of aluminium alloys – table

The table gives indicative solidus and liquidus temperatures for the casting alloys we pour and for several popular wrought alloys. Actual values depend on the exact chemical composition of the melt.

AlloyDesignationSolidusLiquidus
AlSi7MgEN AC-42000approx. 555 °Capprox. 615 °C
AlSi8Cu3EN AC-46200approx. 520–540 °Capprox. 600–620 °C
AlSi9Cu3(Fe)(Zn)EN AC-46500approx. 520–540 °Capprox. 590–610 °C
AlSi12Cu1(Fe)EN AC-47100approx. 560–570 °Capprox. 580–590 °C
AlMg5EN AC-51300approx. 560–580 °Capprox. 630–640 °C
Al 99.5EN AW-1050Aapprox. 646 °Capprox. 657 °C
AlMg1SiCuEN AW-6061approx. 580 °Capprox. 650 °C
AlCu4Mg1EN AW-2024approx. 500 °Capprox. 640 °C
AlZn5.5MgCuEN AW-7075approx. 475 °Capprox. 635 °C

Alloy 7075, which designers often ask about, starts to melt at about 475 °C. It is a wrought alloy that is not used for casting, and its wide freezing range makes it prone to cracking during welding. In high-strength castings its role is usually taken by AlSi7Mg alloys in the T6 temper.

At what temperature is aluminium cast?

The metal poured into the mould must be superheated above the liquidus so that it fills the cavity before it starts to solidify. The pouring temperature is chosen according to the casting method, wall thickness and alloy.

Casting methodTypical metal temperatureTypical mould temperature
Sand molds700–760 °Cambient temperature
Permanent molds680–740 °C250–450 °C
Die casting650–700 °C180–300 °C

Thin-walled sand castings require temperatures from the upper end of the range, heavy castings from the lower end. In a permanent mould the mould temperature is just as important as the metal temperature, which is why our foundry monitors it with a thermal imaging camera. A comparison of the processes can be found in our article on aluminium casting methods.

Why should aluminium not be overheated?

The solubility of hydrogen in molten aluminium increases with temperature, and above about 760–780 °C the oxide layer also grows faster. Metal that is too hot means more pores, more dross and faster wear of crucibles and moulds. That is why the metal is superheated only as much as the process requires and is refined before pouring, as we describe in our article on degassing and refining aluminium.

How much energy does it take to melt aluminium?

To melt 1 kg of aluminium at room temperature, it must be heated to 660 °C and then supplied with the latent heat of fusion. With a specific heat of about 0.9 kJ/(kg·K) and a heat of fusion of about 397 kJ/kg, this gives a theoretical figure of about 1 MJ, or about 0.3 kWh per kilogram. Actual furnace energy consumption is several times higher, because part of the heat is lost to the surroundings and the flue gases.

How is aluminium melted in a foundry?

Aluminium foundries use crucible, reverberatory and induction furnaces, and in high-pressure die casting also holding furnaces at the machines. Our plant operates three melting furnaces with digital process control, which allows us to keep the metal temperature within the range appropriate for each process.

Temperature control during melting

The temperature of molten metal is measured with a sheathed immersion thermocouple, because an optical pyrometer gives incorrect readings on the shiny, oxidised surface of aluminium. Measurements are taken before refining and immediately before the mould is poured.

Heat treatment temperatures and the melting point

The highest temperature in the heat treatment of castings is used for solution treatment, which for AlSi7Mg alloys is carried out at about 525–545 °C, only slightly below the solidus. Exceeding the solidus causes incipient melting at the grain boundaries and an irreversible loss of casting properties. That is why heat treatment furnaces must hold the temperature to within a few degrees. Details of this process are described on our page on solution treatment of aluminium.

Frequently asked questions

What is the melting point of aluminium?

Pure aluminium melts at 660.3 °C. Aluminium alloys melt over a temperature range, usually between about 475 and 660 °C, depending on their chemical composition.

At what temperature does aluminium from cans and profiles melt?

Cans and profiles are made from wrought alloys that melt roughly in the range of 580–660 °C, and for casting they are usually superheated to 700–750 °C. However, such scrap has an uncontrolled composition and coatings, so it is not suitable for engineering castings. Amateur melting is covered in our article on casting aluminium at home.

At what temperature does alloy 7075 melt?

Alloy 7075 starts to melt at about 475 °C and is fully liquid above about 635 °C. The wide melting range results from its high zinc, magnesium and copper content.

Does the melting point matter when choosing an alloy for a casting?

Yes, although indirectly. A low liquidus and a narrow freezing range make it easier to fill thin walls, while the solidus limits heat treatment temperatures. For parts operating at high temperatures, however, strength matters more, and in most aluminium alloys it drops markedly above about 150–200 °C.

Aluminium castings – we will select the alloy and the process

We cast alloys EN AC-42000, EN AC-46200, EN AC-46500, EN AC-47100 and EN AC-51300 in sand moulds, permanent moulds and high-pressure dies. Send us your drawing and requirements, and our process engineer will select the alloy, process parameters and heat treatment for your part. Send your enquiry with a request for a quotation.

Our full offer is presented on the page of our aluminum foundry in Poznań.

Sources and standards

  • ITS-90 – International Temperature Scale of 1990, freezing point of aluminium 660.323 °C.
  • EN 1706 – Aluminium and aluminium alloys. Castings. Chemical composition and mechanical properties.
  • ASM Handbook, Vol. 2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM International.
  • J. Campbell, Complete Casting Handbook, 2nd ed., Butterworth-Heinemann, 2015.

Author: Poznań Foundry team

Poznań Foundry is a brand of Adjatech Metalworking Sp. z o.o., a family-owned non-ferrous foundry in Poznań. The Brukwicki family has been in foundry pattern making since 1950. We cast aluminum alloys in permanent molds, in sand molds and by high-pressure die casting; we machine the castings on CNC machines and powder coat them. We operate under ISO 9001 and ISO 14001 management systems (TÜV Rheinland Polska certificates).

About usCertificatesCompany details

Blog

Read also

More guides on castings, machining and working with a foundry.

All articles

Contact

Have a question about castings?

Send a 2D drawing as a PDF or a 3D model in STEP format, specify the material and quantity, and we will advise on the right process and prepare a quote.

Feel free to contact us by e-mail or phone

Office · Mon–Fri 8:30 a.m.–4:30 p.m.

Poznań Foundry

+48 61 662 43 37odlewnia@adjatech.pl

or visit us in person – you are welcome!

ul. Gnieźnieńska 26
Janikowo near Poznań
62-006 Kobylnica

Office open Mon–Fri 8:30 a.m.–4:30 p.m.

Get directions (Google Maps, new window)

Company details and directions: Contact page