Metal Casting: High-Pressure Die Casting, Permanent Mold Casting and Sand Casting
Aluminium casting methods – types of casting, comparison and choosing the right process
Gravity or pressure, sand or permanent mould? An overview of aluminium casting methods with selection criteria: batch size, wall thickness, tolerances and tooling cost.
Table of contents (10)
- 01What is aluminium casting?
- 02Sand casting
- 03Gravity die casting in permanent steel moulds
- 04Aluminum high-pressure die casting
- 05Special methods: low-pressure, investment casting and others
- 06Comparison of aluminium casting methods
- 07How to choose the casting method for your part
- 08Frequently asked questions
- 09Aluminium foundry – we will choose the method for your part
- 10Sources and standards
Aluminium casting methods fall into two groups: gravity casting, in which molten metal fills the mould under its own weight, and pressure casting, in which the metal is forced into a steel mould. Industry relies on three main processes: sand moulds, permanent moulds (gravity dies) and high-pressure die casting. This guide compares them with special processes and shows how to match the process to batch size, geometry and customer requirements.
In brief
- The casting method determines tooling cost, unit price, dimensional accuracy and whether the part can be heat treated.
- Sand moulds pay off for prototypes and short runs, gravity dies from a few hundred parts, and high-pressure die casting for volumes in the tens of thousands.
- Gravity castings (sand and permanent mould) have lower porosity and can be heat treated to the T6 temper, which is normally not done with die castings.
- High-pressure die casting gives the thinnest walls, around 1–2 mm, and the smoothest surface, while sand moulds allow the largest parts at the lowest tooling cost.
- Special processes such as low-pressure or investment casting solve specific problems, but they are rarely the first choice for a typical machine component.
What is aluminium casting?
Casting means producing a part by pouring molten metal into a mould whose cavity reproduces the shape of the component. The finished part is called a casting. Aluminium is well suited to casting because it melts at a relatively low temperature and its silicon alloys readily fill thin mould sections. Temperature ranges for individual alloys are listed in our article on the melting point of aluminium.
Every method follows the same stages: mould preparation, melting and refining, pouring, solidification, removal of the casting, removal of the gating system and finishing. The methods differ in what the mould is made of and how the metal fills it. The full sequence is described in our article on the stages of the aluminium casting process.
Gravity casting versus pressure casting
In gravity casting the metal flows into the cavity under its own weight, calmly and relatively slowly. In pressure casting it is driven by a plunger or by gas pressure, and the mould fills in a fraction of a second instead of several seconds. This difference affects porosity, the minimum wall thickness and the possibility of heat treatment.
Expendable moulds and permanent moulds
A sand mould is used for a single pour and is destroyed when the casting is knocked out. Permanent moulds and die-casting dies are made of steel and produce thousands or even hundreds of thousands of castings. An expendable mould is cheap, but each one has to be made from scratch. A permanent mould is expensive, but its cost is spread over the whole production run.
Sand casting
In this method the mould cavity is formed with a pattern in moulding sand mixed with a binder, while holes and internal channels are formed by cores. Sand moulds make it possible to cast large and complex parts at low tooling cost, because the pattern can be made of wood or resin.
Advantages and limitations of sand castings
- Advantages of – low pattern cost, short lead time, large part sizes, freedom in designing internal cavities and the option of T6 heat treatment.
- Limitations – rough surface, larger machining allowances and tolerances, longer cycle time and thicker minimum walls, usually from about 4–5 mm.
The type of moulding sand and how it is compacted affect the accuracy and surface finish of the casting, as we explain in our article on molding sands.
When should you choose a sand mould?
A sand mould is the first choice for prototypes, one-off castings, runs of up to a few hundred parts and large parts. It also works well when the design may still change, because modifying a pattern costs a fraction of reworking a permanent mould. How we work with this process is shown on our page on aluminum sand casting.
Gravity die casting in permanent steel moulds
A permanent mould is a reusable steel mould into which molten aluminium is poured by gravity, often while tilting the mould for calmer filling. The metal gives off heat quickly to the steel, so the casting has a finer structure, better mechanical properties and a smoother surface than a sand casting. Cavities that cannot be formed with steel cores are made with sand cores.
Parameters of gravity die castings
- The surface is clearly smoother than in a sand mould, and tolerances usually fall within grades DCTG 6–8 according to ISO 8062-3.
- The minimum wall thickness is usually about 3–4 mm.
- Gravity die castings made from AlSi7Mg alloys can be solution treated and aged to the T6 temper.
- A permanent mould typically withstands from about ten thousand to several tens of thousands of pours, depending on the alloy, geometry and maintenance.
Permanent mould cost and break-even volume
A permanent mould costs many times more than a pattern for a sand mould, but for runs from a few hundred to several tens of thousands of parts it gives a lower unit price and better repeatability. Mould temperature affects casting quality, which is why our foundry measures it with a thermal imaging camera. Details of this process are presented on our page on aluminum permanent mold casting.
Aluminum high-pressure die casting
In high-pressure die casting (HPDC) molten aluminium is injected at high speed into a steel die by a plunger, and at the end of filling it solidifies under high intensification pressure. Aluminium alloys are processed on cold-chamber machines. A cycle takes from around ten seconds to about a minute, making this the most productive casting method.
Advantages of high-pressure die casting
- The thinnest walls, around 1–2 mm, and excellent reproduction of fine details.
- The smoothest surface and the tightest tolerances among casting methods, usually DCTG 5–7.
- Short cycle times and the lowest unit cost in high-volume production.
Limitations: porosity and heat treatment
Fast, turbulent filling traps air and gases from die release agents inside the casting. That is why a typical die casting is not solution treated and aged to the T6 temper, as blisters may form on its surface during heating. The die is also the most expensive type of mould, so the method pays off in high volumes, in our case up to 100,000 parts per year. More information is available on our page on aluminum die casting.
Special methods: low-pressure, investment casting and others
Besides the three main processes there are several methods for special tasks. They are worth knowing, because sometimes they solve a problem better than a compromise within a conventional process.
Low-pressure die casting (LPDC)
The metal is pushed from a sealed furnace through a riser tube into a mould placed above it, usually at an overpressure of less than 1 bar. Bottom filling is calm and metal yield is high, which is why aluminium wheels, among other parts, are made this way. The method requires an expensive, specialised machine and pays off in large, repeatable runs.
Investment casting (lost wax)
A wax pattern is coated with layers of ceramic slurry, the wax is melted out and the resulting shell is filled with metal. The method produces very accurate castings with a smooth surface, including shapes that are impossible in a split mould. However, it is expensive and usually limited to small parts.
Centrifugal casting, plaster mould casting and lost foam casting
Centrifugal casting is used for rotationally symmetrical parts such as bushings. Plaster moulds give smooth surfaces for prototypes, and the lost foam process makes it possible to cast complex shapes without cores. These are niches worth considering only when conventional methods cannot meet the requirements.
Comparison of aluminium casting methods
The table summarises typical parameters of the three main processes. The values are indicative and depend on geometry, alloy and drawing requirements.
| Criterion | Sand mold | Permanent mold | Die casting |
|---|---|---|---|
| Typical batch size | from 1 to several hundred parts | from several hundred to several tens of thousands of parts | from several thousand to over 100,000 parts per year |
| Tooling cost | low | medium | high |
| Minimum wall thickness | approx. 4–5 mm | approx. 3–4 mm | approx. 1–2 mm |
| Typical tolerance grade to ISO 8062-3 | DCTG 7–12 | DCTG 6–8 | DCTG 5–7 |
| Surface roughness Ra | 12.5–25 µm | 3.2–12.5 µm | 1.6–6.3 µm |
| T6 heat treatment | yes | yes | usually not |
| Casting size | largest | medium | limited by machine size |
| Time to start production | shortest | medium | longest |
How to read DCTG grades and machining allowances is explained in our article on casting tolerances according to ISO 8062-3.
How to choose the casting method for your part
Selection starts with questions about volume, geometry and functional requirements, not with the process itself. The process engineer compares this data with tooling cost and the unit price over the whole product life cycle.
Quantity and production horizon
Prototype and pilot batch
For up to a few dozen parts, and while the design is still changing, a sand mould is the most sensible choice. It lets you test the part in assembly and in trials without investing in a permanent mould.
Series production
With a stable drawing and runs counted in hundreds or thousands of parts per year, a permanent mould pays off, and for tens of thousands – a high-pressure die. A cost comparison of both solutions is given in the article gravity die casting vs high-pressure die casting – a comparison of technology, cost and quality.
Geometry, walls and internal cavities
Thin, extensive walls and many ribs point towards high-pressure die casting. Deep cavities and internal channels that cannot be produced with die slides require sand cores, and therefore a sand mould or a permanent mould. Principles for shaping a casting for the chosen method are described in our guide to designing aluminium castings.
Strength, pressure tightness and heat treatment
If the casting has to carry high loads, be welded or be hardened to the T6 temper, gravity casting is usually chosen. When pressure tightness matters in high-volume production, high-pressure die casting is combined with impregnation or vacuum-assisted casting. The differences between the two gravity methods are discussed in the article sand or gravity die castings – which to choose.
Frequently asked questions
Which aluminium casting method is the cheapest?
For a few or a few dozen parts a sand mould is the cheapest, because the pattern costs little. In high-volume production high-pressure die casting gives the lowest unit price despite the most expensive die. A permanent mould is the intermediate solution. The components of the price are described in our article how much an aluminum casting costs.
What is the difference between gravity casting and pressure casting?
In gravity casting the metal fills the mould under its own weight, while in pressure casting it is injected at high speed and solidifies under pressure. Gravity castings contain fewer pores and can be heat treated. Die castings have thinner walls, a smoother surface and tighter tolerances.
Can the casting method be changed during a project?
Yes, and this is common practice: prototypes are cast in sand, and once the design is approved, production moves to a permanent mould or a high-pressure die. From the outset, however, the part should be designed with the target method in mind, because draft angles, wall thicknesses and allowances change.
Which aluminium alloys are used in each method?
Gravity casting often uses AlSi7Mg alloys, which respond well to heat treatment. High-pressure die casting is dominated by copper-containing alloys such as AlSi9Cu3(Fe)(Zn) and AlSi8Cu3, as well as AlSi12Cu1(Fe). An overview of the alloys we cast is available on our page on aluminum alloys.
Aluminium foundry – we will choose the method for your part
We cast aluminium in sand moulds, permanent moulds and high-pressure dies, so we do not have to force your design into a single process. Send us a 2D drawing in PDF or a 3D model in STEP format, the material and the planned quantity, and our process engineer will propose the method, tooling and scope of machining. Send the complete data with a request for a quotation.
Our processes, machinery and certificates are presented on the page of our aluminum foundry in Poznań.
Sources and standards
- EN 1706 – Aluminium and aluminium alloys. Castings. Chemical composition and mechanical properties.
- ISO 8062-3 – Dimensional and geometrical tolerances and machining allowances for castings.
- J. Campbell, Complete Casting Handbook, 2nd ed., Butterworth-Heinemann, 2015.
- ASM Handbook, Vol. 15: Casting, ASM International.
Author: Poznań Foundry team
Poznań Foundry is a brand of Adjatech Metalworking Sp. z o.o., a family-owned non-ferrous foundry in Poznań. The Brukwicki family has been in foundry pattern making since 1950. We cast aluminum alloys in permanent molds, in sand molds and by high-pressure die casting; we machine the castings on CNC machines and powder coat them. We operate under ISO 9001 and ISO 14001 management systems (TÜV Rheinland Polska certificates).



