Density of aluminium – table for alloys and how to calculate casting mass
What the density of aluminium and its alloys is, how it changes with temperature, how to calculate the mass of a casting and how density measurement helps to detect porosity.
Table of contents (8)
- 01What is the density of aluminium?
- 02Density of aluminium alloys – table
- 03How to calculate the mass of an aluminium casting
- 04How does the density of aluminium change with temperature?
- 05Density measurement and casting porosity
- 06Frequently asked questions
- 07Lightweight aluminium castings made to order
- 08Sources and standards
The density of aluminium is 2.70 g/cm³, or 2700 kg/m³ (for the pure metal at 20 °C, precisely about 2698 kg/m³). That is roughly one third of the density of steel. The density of casting alloys usually lies between 2.64 and 2.76 g/cm³ and depends mainly on their silicon, magnesium and copper content. Below you will find a table of alloy densities, the formula for casting mass and practical uses of this value in a foundry.
In brief
- The density of pure aluminium is 2.70 g/cm³ (2700 kg/m³), or about 34% of the density of steel.
- Silicon and magnesium slightly reduce the density of an alloy, while copper and zinc increase it, which is why AlSiCu alloys are heavier than AlSiMg alloys.
- The mass of a casting is calculated by multiplying the volume from the CAD model by the alloy density.
- Liquid aluminium has a density of about 2.37 g/cm³, so it shrinks by 6–7% in volume as it solidifies, which must be compensated for by feeders.
- Comparing the measured density of a casting with the density of the alloy makes it possible to estimate its porosity.
What is the density of aluminium?
At room temperature pure aluminium has a density of 2.70 g/cm³. In different units the same value looks like this.
| Certification body | Density of aluminium |
|---|---|
| g/cm³ | 2,70 |
| kg/m³ | 2700 |
| kg/dm³ | 2,70 |
| t/m³ | 2,70 |
| lb/in³ | 0,0975 |
For engineering calculations a value of 2.70 g/cm³ is usually assumed for pure and commercially pure aluminium, while for alloys the value from the material data sheet or from the table later in this article is used.
Density of aluminium compared with other materials
Low density is the main reason why aluminium replaces steel and cast iron in structures where weight matters.
| Material | Density [g/cm³] |
|---|---|
| Polyamide PA6 | approx. 1.14 |
| Polyamide PA6 with 30% glass fibre | approx. 1.36 |
| Magnesium | 1,74 |
| Aluminum | 2,70 |
| Titanium | 4,51 |
| Gray cast iron | approx. 7.1–7.2 |
| Carbon steel | approx. 7.85 |
An aluminium casting is therefore almost three times lighter than the same casting made of cast iron. A comparison of the properties of both materials is given in the article aluminium or cast iron for a casting.
Density of aluminium alloys – table
Alloying elements change the density of aluminium slightly but measurably. Silicon (2.33 g/cm³) and magnesium (1.74 g/cm³) are lighter than aluminium, while copper, zinc and iron are heavier.
| Alloy | Designation | Density [g/cm³] |
|---|---|---|
| AlSi7Mg | EN AC-42000 | approx. 2.67–2.68 |
| AlSi8Cu3 | EN AC-46200 | approx. 2.75 |
| AlSi9Cu3(Fe)(Zn) | EN AC-46500 | approx. 2.75–2.76 |
| AlSi12Cu1(Fe) | EN AC-47100 | approx. 2.65–2.68 |
| AlMg5 | EN AC-51300 | approx. 2.64–2.65 |
| Al 99.5 | EN AW-1050A | 2,70 |
| AlMg1SiCu | EN AW-6061 | 2,70 |
| AlZn5.5MgCu | EN AW-7075 | 2,81 |
The values are indicative. The density of a specific melt depends on its actual chemical composition, and differences of 0.01–0.02 g/cm³ matter only for very precise mass balances. Alloy designations are explained in our article on cast aluminium alloy designations.
How to calculate the mass of an aluminium casting
The mass of a casting is calculated with the formula m = V × ρ, where V is the volume of the casting and ρ is the density of the alloy. The volume is most conveniently read from the 3D model in CAD software, taking care to use consistent units.
Example of a casting mass calculation
A housing with a volume of 420 cm³ cast from AlSi7Mg alloy with a density of 2.68 g/cm³ weighs 420 × 2.68 = 1126 g, i.e. about 1.13 kg. The same part made from AlSi9Cu3(Fe)(Zn) alloy with a density of 2.76 g/cm³ will weigh about 1.16 kg, and in cast iron with a density of 7.2 g/cm³ about 3.02 kg.
Raw casting mass versus finished part mass
- The CAD model of the finished part does not include machining allowances, so the raw casting is heavier, usually by a few to more than ten per cent.
- The mass of poured metal also includes the gating system and feeders, which in gravity casting can account for one third to one half of the metal poured into the mould.
- Cavities formed by cores reduce the mass of the casting, but not the cost of the mould or the cores.
The role of the gating system in the metal balance is described in our article on the gating system.
Density and casting price
The mass of a casting is one of the main components of its price, because it affects metal and energy consumption and the cycle time. That is why, when comparing quotations, it is worth checking which density and allowances were used in the calculation. The other components of the price are discussed in our article how much an aluminum casting costs.
How does the density of aluminium change with temperature?
Aluminium expands when heated, so its density decreases as the temperature rises. The coefficient of thermal expansion of pure aluminium is about 23 × 10⁻⁶ 1/K and that of AlSi alloys about 20–22 × 10⁻⁶ 1/K, almost twice as much as for steel.
Density of liquid aluminium
At its melting point liquid aluminium has a density of about 2.37 g/cm³. The difference compared with the solid metal means a volumetric solidification shrinkage of about 6–7%, which the foundry compensates for with feeders and directional solidification. The melting ranges of the alloys are given in our article on the melting point of aluminium.
Linear shrinkage and pattern dimensions
After solidification the casting continues to contract as it cools to ambient temperature. That is why patterns and permanent moulds are made larger than the casting by the pattern shrinkage allowance, which for aluminium alloys is usually about 1.0–1.3%. It is taken into account by our foundry pattern-making.
Density measurement and casting porosity
Density measured by the Archimedes method, i.e. by weighing a sample in air and in water, makes it possible to assess how many pores a casting contains. Porosity is calculated as the difference between the alloy density and the measured density, divided by the alloy density.
Example of a porosity calculation
If a sample of AlSi7Mg alloy with a theoretical density of 2.68 g/cm³ has a measured density of 2.63 g/cm³, its porosity is (2.68 − 2.63) / 2.68 × 100% ≈ 1.9%. Such a result in a loaded area should prompt a check of metal refining and casting feeding.
Density index of the molten metal
The same principle is used to check the metal before pouring. Samples solidified under vacuum and in air are compared and a density index is calculated: the higher it is, the more hydrogen the metal contains. Methods of assessing and reducing porosity are described in our article on aluminium casting defects.
Frequently asked questions
What is the density of aluminium in kg/m³?
The density of aluminium is 2700 kg/m³, which corresponds to 2.70 g/cm³ and 2.70 kg/dm³. The density of popular casting alloys ranges from about 2640 to 2760 kg/m³.
How much does 1 dm³ of aluminium weigh?
One cubic decimetre, i.e. one litre, of pure aluminium weighs about 2.70 kg. The same volume of steel weighs about 7.85 kg and of cast iron about 7.2 kg.
Is aluminium lighter than steel?
Yes, almost three times lighter: the density of aluminium is 2.70 g/cm³, while that of steel is about 7.85 g/cm³. However, aluminium has a lower modulus of elasticity, about 70 GPa compared with about 210 GPa for steel, so a lightweight design requires suitably shaped ribs and cross-sections.
Which density should be entered in the CAD model of a casting?
Ideally the value for the specific alloy from the material data sheet or from the table above. Using the default density of 2.70 g/cm³ for AlSi9Cu3(Fe)(Zn) alloy underestimates the mass of the casting by about 2%, which in high-volume production matters for costing and logistics.
Lightweight aluminium castings made to order
We cast aluminium alloys in sand moulds, permanent moulds and high-pressure dies, and we calculate the mass and cost of the casting at the quotation stage from the 3D model. Send us a model in STEP format or a drawing with the material and quantity, and you will receive a quotation including the raw casting mass. Send the data with a request for a quotation.
You can read about our processes and alloys on the page of our aluminum foundry in Poznań.
Sources and standards
- EN 1706 – Aluminium and aluminium alloys. Castings. Chemical composition and mechanical properties.
- ASM Handbook, Vol. 2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM International.
- J. R. Davis (ed.), Aluminum and Aluminum Alloys, ASM Specialty Handbook, ASM International, 1993.
- J. Campbell, Complete Casting Handbook, 2nd ed., Butterworth-Heinemann, 2015.
Author: Poznań Foundry team
Poznań Foundry is a brand of Adjatech Metalworking Sp. z o.o., a family-owned non-ferrous foundry in Poznań. The Brukwicki family has been in foundry pattern making since 1950. We cast aluminum alloys in permanent molds, in sand molds and by high-pressure die casting; we machine the castings on CNC machines and powder coat them. We operate under ISO 9001 and ISO 14001 management systems (TÜV Rheinland Polska certificates).




